LCN-GTS2TC Issendorff KG

Active transponder system for wall mounting The LCN-ATW is an active transponder system designed for wall mounting. It provides access control with a large range and allows for convenient door opening without the need for a conventional key. When a person approaches the antenna, the active transponder is activated and transmits its ID. Application examples Automatic door opening in residential and commercial buildings. Integration into modern security systems. The LCN-ATW stores multiple transponders in the field and outputs them sequentially to the I connection of a bus module. The transponders are available in various designs, including with buttons for remote control functions. Technical data Dimensions: 160 mm x 250 mm x 90 mm (W x H x D) Protection class: IP65

Sensor/Actuator Module for Flush-Mounting Box Combined sensor/actuator module with two electronic switching outputs 230V, 300VA. Dimmable in phase-cut or as a switch (switches at zero crossing). The 8 button inputs can individually control 64 target addresses with 192 functions. Integrated pulse measurement input for remote control receivers. The built-in operating program includes the following functions: switching and dimming of the outputs, brightness and change speed can be set separately. Includes programs for incandescent lamp dimming, blinds, gates, etc. Evaluation via 5 thresholds (=10 commands) with hysteresis. Includes 2 continuous controllers that can be used independently and additionally for threshold processing. Two measurement sizes can be captured and controlled independently of each other. Decoding of telegrams from the IR remote control receiver or transponder. Evaluation directly or via central computer. Functions for button levels, coded transmission, sender differentiation. Additional functions: control with dependencies, forming links, counting, calculating, fixed and dynamic group formation, generating automatic status messages (real feedback) for visualization. LCN System Bus Functions Communication with up to 30,000 modules, max. 250 modules per bus level. Protocol with collision avoidance Documentation and parameterization retrievable in the module memory 100 light scene memories available per output Connection options for EIB/KNX touch sensors (standard), DSI-Dali interface, relays Overload protection, the outputs switch off consumers at too large loads Note: UPP modules must not be connected directly to roller or blind motors! The limit switches or the triacs in the module may be damaged. It is recommended to use the isolation relay LCN-R2U. A filter (LCN-FI1) is mandatory as soon as the electronic outputs of the LCN-UPP are used as dimmers. The interference filter is connected between the module and the consumer, dampening the disturbances that occur during dimming, thus ensuring compliance with CE standards. Technical Data Integrated power supply 230V ±15%, 0.4W, pulse-proof up to 4kV. Flush-mounted housing, connection via approx. 20cm long single wires 0.75mm². Dimensions: 50mm Ø x 20mm. Protection class IP20

Adapter for extending and duplicating the I connection for DIN rail The LCN-IVH is an enhanced version of the LCN-IV adapter, specifically designed for DIN rail mounting. It allows for the doubling of the I connection and can also be combined with up to two LCN-IVH adapters to extend the range of the I connection with IY(ST)Y 2x2x0.8mm up to 50m. The LCN-IVH additionally acts as a pulse sensor that evaluates a 5V signal via potential-free contacts. Application Areas This adapter is particularly useful in installations where multiple sensors need to be operated on a bus module. It enables flexible and decentralized installation of sensors such as remote control receivers, temperature sensors, and binary sensors. Technical Data Frequency: maximum 500 Hz Dimensions: 17mm x 92mm x 66mm (W x L x H) DIN rail mounting: 35mm, 1TE Protection class: IP20

Adapter for extending and duplicating the I connection The LCN-IV is a versatile adapter designed to extend and duplicate the I connection. It allows the connection of up to two LCN-IV adapters to extend the I connection with IY(ST)Y 2x2x0.8mm up to 50m. Additionally, the LCN-IVH acts as a pulse sensor that evaluates a 5V signal via potential-free contacts. Application Areas This adapter is ideal for applications where multiple sensors need to be operated on a bus module. It enables flexible and decentralized installation of sensors such as remote control receivers, temperature sensors, and binary sensors. Technical Data Frequency: maximum 500 Hz Dimensions: 14mm x 21mm x 12mm (W x L x H)

Issendorff LCN-IK70LCN-IK70

LCN-PINZ Issendorff KGLCN-PINZ